Road construction work can be frustrating, but it helps maintain infrastructure and is a necessary fact of life for all drivers. Whether you drive for commercial purposes, commute on a regular basis or go for the daily school run. The delays and frustration brought on by traffic congestion as a result of a work zone can make even the most patient person run out of patience. That can be very risky and dangerous, drivers need to be cautious and aware of the risks involved in a work zone collision

In particular, there is a high potential for rear-end collisions. These collisions are the most common type of crash in a work zone and it usually occurs when a driver hits the rear-end of a car slowing down or coming to a halt. Most drivers can avoid a collision like this if they simply slow down and create sufficient space between the car in front of them.  Another possible collision can occur with the work crew and their equipment and with the barriers that barricade the lanes. The roads often have an uneven surface and the lanes are scattered back and forth in different directions. 

Driving in work zones doesn’t have to be an ordeal, Safely passing through these circumstances requires patience and careful driving. You also have to be mindful of those around you in order to increase the safety of everyone on the road. If you’re driving through work zones, here are a few safety tips to bear in mind 

  1. MINIMISE ALL DISTRACTIONS

Workzone rear-end collision often happens because of distractions. A mother may try to calm her crying toddler in the back seat, a motorist might look at the construction workers or a map to find alternative routes. A distracted driver doesn’t see when a car in front slows down or stops. As a result of this, a rear-end collision occurs. If you’re driving in a work zone area, you should minimise all forms of distractions and direct your full attention on the road. Never multitask while driving especially through a congested work zone. Turn off the radio and put away your phone. If your kids are acting up in the back seat, take care of their needs until you’re out of the work zone area. Ensure your car ac is working well, get an auto air conditioning service if it’s faulty. During summer the heat gets worse and driving in a hot car will cause even more discomfort while getting distracted in the process. Avoid conversations to prevent any distraction and focus on the road ahead of you.

  1. PAY ATTENTION TO BRAKE LIGHTS. 

Pay attention to brake lights on the vehicles in front of you and the traffic around you. A vehicle may suddenly stop in front of you so being alert is important. Ensure you create enough space between vehicles so that you can safely come to a stop. Be most watchful when merging into another lane, avoid tailgating. Ensure your car parts are in good shape, don’t go out driving with a faulty brake or a weak battery. Get a car battery replacement if your battery is bad. Look out for authentic nz car parts to replace any faulty part of your car. 

Your car has to be in good shape, you don’t want your car to break down right in the middle of a busy work zone area only because you forgot to charge your battery or change your oil. Also, know that traffic patterns in work zones can change on a daily basis, so don’t become smug if you pass the same route daily.

  1. SLOW DOWN.

More than one-third of severe crashes in the work zone is as a result of speeding. Workzone areas require slower driving than normal. Speed zone signs are normally are usually posted, ensure you obey the posted limits as workers maybe a few feet away from your car. Be considerate and drive with their safety in mind. Remember, you could be charged double fine if you break posted rules while driving through work zone areas. Be patient, no work zone area will be there forever, so slow down and pass through the area in one piece.

  1. MERGE PROPERLY

If you see a lane is closing up ahead of you, merge as soon as possible to avoid a frustrating lane change. It doesn’t mean you have to drive in a rush in a bid to join the closing lane. Most highway work zone collision are as a result of impatient drivers forcing their way into lanes. 

Be mindful when merging with lanes, you should do so only where the road markings indicate and if traffic permits.

  1. BE PREPARED FOR THE UNEXPECTED:

Events can alter quickly in work zones. Construction equipment can fall into the roadway, traffic lanes can merge or traffic could slow or stop without warning. You have to be aware of and prepared for the unexpected. One of the best ways to prevent an accident caused by a distracted driver is by avoiding distracted drivers around you. If you see a driver reaching in their back seat, answering a phone call or appears to be distracted in any form, allow them to go ahead or pass them. Don’t purchase cars that will be a problem when driving along these congested work zone. If used cars are your thing, or if you’re looking to buy a ford transit van for sale, buy from a trusted dealer. Remember to check your car’s fluid levels, if it’s low, check for a transmission shop near you. You don’t want your car to be the cause of an accident you could have otherwise prevented. If you’re on a two-lane road and you notice the driver tailgating you, drive to the corner and let them pass. Whatever you do, create enough space as possible between them and you.

BOTTOM LINE

Highway work zones can be dangerous areas for drivers and construction workers but it doesn’t always have to be the case. By practising proper safety habits, you can reduce the risks of encountering a collision caused by a distracted driver. 

Sharing is caring!

Leave a Reply

Your email address will not be published. Required fields are marked *